+92 312 1007722
Phone number
info@malikcorporation.pk
Email address
46-C Lane 3, Phase-6, D.H.A , Karachi
Address location
Phone number
Email address
Address location
Showing the single result
A CPVC piping system is only as leak-proof as the joints bonding it together, and the strength of that bond depends almost entirely on the solvent cement used to make it. Malik Corporation supplies genuine AGM CPVC Solvent Cement nationwide across Pakistan, as the country’s sole authorized agent for Arabian Gulf Manufacturers Company Ltd. (AGM). Unlike AGM’s pipe and fitting lines, which are produced in Jeddah, Saudi Arabia, AGM’s solvent cement branded AGM 914 for CPVC is manufactured in the USA, reflecting a formulation built specifically around CPVC’s chemical structure rather than general-purpose plastic bonding.
Solvent cement isn’t an adhesive in the traditional sense — it doesn’t glue two surfaces together mechanically. Instead, it chemically softens the surface layers of both the CPVC pipe and fitting, allowing the two plastic surfaces to fuse into a single, continuous wall as the solvents evaporate and the joint cures. This process, called solvent welding, is why a properly cemented CPVC joint doesn’t behave like a sealed connection that can loosen over time — it behaves like one uninterrupted piece of pipe. That distinction matters most in systems under constant pressure or temperature cycling, such as hot-water lines, where a mechanically sealed joint is far more likely to fail than a fused one.
AGM 914 is an orange-colored, heavy-bodied, high-strength, medium-setting solvent cement formulated to ASTM Type IV, Grade 1 classification a designation that specifies both the cement’s chemical composition and its intended performance characteristics for CPVC applications. The heavy-bodied formulation is deliberate: it fills gaps more effectively than thin-bodied cement, which matters for interference-fit joints where pipe and fitting tolerances aren’t perfectly uniform. Medium setting time gives installers enough working time to align fittings correctly before the joint begins curing, reducing the risk of misaligned connections in larger or more complex piping runs.
The cement is rated for use across pipe and fitting sizes up to 12″, making it suitable for everything from small residential branch lines to large commercial and industrial CPVC installations. It performs reliably across both hot and cold water systems, and is approved for compatible third-party CPVC products, including FlowGuard pipe and fittings a practical consideration for contractors working across mixed-brand installations. AGM 914 is supplied in container sizes ranging from 118ml to 946ml, allowing both small repair jobs and large-scale bulk installations to be sized appropriately without excess waste.
AGM’s CPVC solvent cement is tested to defined pressure benchmarks rather than marketed on durability claims alone: joints bonded with AGM 914 are rated to withstand a 2-hour hydrostatic burst test at 400 psi and a 4-hour sustained pressure test at the same rating. These are the kinds of standardized performance checks that distinguish a genuine, quality-controlled solvent cement from unbranded or counterfeit alternatives sometimes found in local markets a meaningful concern, since a weak or incompatible cement is one of the most common causes of early joint failure in CPVC systems, regardless of how high-quality the pipe and fittings themselves are.
Beyond standard hot and cold water plumbing, AGM 914 is suited to irrigation lines, drainage, waste and vent systems, sewer connections, and electrical conduit work — essentially any application using CPVC pipe and fittings where a permanent, pressure-rated joint is required. Its versatility across both potable water and industrial use cases makes it a standard stock item for plumbers and contractors working across varied project types, rather than a specialty product needed for one narrow application.
Because solvent cement is consumed quickly and often reordered, it’s also a product category where counterfeit or relabeled alternatives circulate more easily than with pipes or fittings. As AGM’s sole agent in Pakistan, Malik Corporation imports AGM 914 directly, giving contractors and distributors a verifiable source for genuine product rather than relabeled generic cement. With decades of experience supplying Pakistan’s piping and plumbing trade, Malik Corporation stocks solvent cement in bulk alongside its full AGM pipe and fitting range, so installers can source matched, compatible components from a single supplier.
It’s used to chemically fuse CPVC pipe and fittings into permanent, pressure-rated joints for hot and cold water plumbing, irrigation, drainage, sewer, and conduit applications.
Yes. AGM 914 is formulated for both hot and cold water CPVC systems and maintains joint integrity under sustained pressure and temperature.
It’s supplied from 118ml up to 946ml, covering small repair jobs through to large bulk installations.
Yes, it’s approved for use with compatible CPVC products including FlowGuard pipe and fittings, in addition to AGM’s own CPVC range.
Yes. Malik Corporation is the sole agent for AGM in Pakistan, with exclusive rights to import and distribute AGM’s full pipe, fitting, and solvent cement range nationwide.